Has anyone heard of head tube issues on the most recent generation of TR11s? A buddy of mine just dented his second frame in 2 months...
Has anyone heard of head tube issues on the most recent generation of TR11s? A buddy of mine just dented his second frame in 2 months behind the headtube from the fork bumpers.
Those ODI bumpers will dent/crack most frames in a crash
Ouch! I was recently following a different thread with people discussing using double crown forks on more enduro level bikes, some of which were not rated for that use. Is there any consensus on what the best bumper setup is to prevent frame damage? It would seem like it would somewhat depend on the frame contours and wall thickness, but even if we put that aside, I sort of go back and forth puzzling it out in my head as far as the optimal durometer and shape of the bumpers. For example, thicker will potentially have more cush, but strike the frame more often. Softer will provide more compliance and gradual ramp up, but might bottom out and spike the loads to the frame. Etc...
Has anyone heard of head tube issues on the most recent generation of TR11s? A buddy of mine just dented his second frame in 2 months...
Has anyone heard of head tube issues on the most recent generation of TR11s? A buddy of mine just dented his second frame in 2 months behind the headtube from the fork bumpers.
Ouch! I was recently following a different thread with people discussing using double crown forks on more enduro level bikes, some of which were not rated...
Ouch! I was recently following a different thread with people discussing using double crown forks on more enduro level bikes, some of which were not rated for that use. Is there any consensus on what the best bumper setup is to prevent frame damage? It would seem like it would somewhat depend on the frame contours and wall thickness, but even if we put that aside, I sort of go back and forth puzzling it out in my head as far as the optimal durometer and shape of the bumpers. For example, thicker will potentially have more cush, but strike the frame more often. Softer will provide more compliance and gradual ramp up, but might bottom out and spike the loads to the frame. Etc...
After some armchair engineering, I think ideally it would be moulded and adhered to the frame itself and sized so that it makes as much contact with the fork as possible, at which point you could relax on the thickness and hardness a bit. It could be a lot of work on more complex frame shapes, but you could also get contact with more than 100 mm of the stanchion on some frames.
Or use a knockblock style headset? The headtube is stronger than the downtube and top tube and can also reroute the loads to the two tubes over a larger surface area than bumpers can... Or a steering damper, it should prevent fast movements and thus high speed impacts.
Contoured bumpers will also have a different stiffness characteristic over the height of the frame so might be semi effective. Thick, somewhat soft bumpers should be the best, but will impact the steering angle.
Or use a knockblock style headset? The headtube is stronger than the downtube and top tube and can also reroute the loads to the two tubes...
Or use a knockblock style headset? The headtube is stronger than the downtube and top tube and can also reroute the loads to the two tubes over a larger surface area than bumpers can... Or a steering damper, it should prevent fast movements and thus high speed impacts.
Contoured bumpers will also have a different stiffness characteristic over the height of the frame so might be semi effective. Thick, somewhat soft bumpers should be the best, but will impact the steering angle.
SRAM just bought O-Chain. Why not shrink their design into a headset?
(Tiny elastomer things pour out like rain onto my deck with gaps)
🫠
Oh man, the deck with gaps comment brought back memories of doing the OneUp 1x conversion to a Shimano 2x10 derailleur about 15 years ago, and having a few spring loaded parts explode then fall through gaps in my deck. That led to trying to hunt down a new assembly of whatever parts exploded, which was non-trivial to find.
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain...
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.
Looks quite similar to Bird frames at first glance...
As far as I could tell, I don't think it's a URT. That lower mount on the frame isn't a pivot, it's just the lower attachment point for the plates that that carry the BB. Then there a traditional horst rear end attached to the plates.
It's like the modular rear end angle they were going for fell flat and so they're making it about frame compliance now. It's a dumb idea, and they would be better off just making bikes like Reeb does.
Ouch! I was recently following a different thread with people discussing using double crown forks on more enduro level bikes, some of which were not rated for that use. Is there any consensus on what the best bumper setup is to prevent frame damage? It would seem like it would somewhat depend on the frame contours and wall thickness, but even if we put that aside, I sort of go back and forth puzzling it out in my head as far as the optimal durometer and shape of the bumpers. For example, thicker will potentially have more cush, but strike the frame more often. Softer will provide more compliance and gradual ramp up, but might bottom out and spike the loads to the frame. Etc...
After some armchair engineering, I think ideally it would be moulded and adhered to the frame itself and sized so that it makes as much contact with the fork as possible, at which point you could relax on the thickness and hardness a bit. It could be a lot of work on more complex frame shapes, but you could also get contact with more than 100 mm of the stanchion on some frames.
Or use a knockblock style headset? The headtube is stronger than the downtube and top tube and can also reroute the loads to the two tubes over a larger surface area than bumpers can... Or a steering damper, it should prevent fast movements and thus high speed impacts.
Contoured bumpers will also have a different stiffness characteristic over the height of the frame so might be semi effective. Thick, somewhat soft bumpers should be the best, but will impact the steering angle.
Thought everyone just put some electrical tape in the right area and just wedge the standard fox ones on the tape....
Has worked perfectly for me
SRAM just bought O-Chain. Why not shrink their design into a headset?
Lemme just grease this headset…
(Tiny elastomer things pour out like rain onto my deck with gaps)
🫠
Oh man, the deck with gaps comment brought back memories of doing the OneUp 1x conversion to a Shimano 2x10 derailleur about 15 years ago, and having a few spring loaded parts explode then fall through gaps in my deck. That led to trying to hunt down a new assembly of whatever parts exploded, which was non-trivial to find.
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.

This looks interesting..
Looks quite similar to Bird frames at first glance...
That's one word for it.
Their IG is full of AI bike vids. I don’t care about their frames. F that crap.
"hey, the new Keeper Co shreddit is out!" said no one?
Yay! URTs are back!
*checks watch
Yep, it's been about 20 years since the URT heyday do they're due any day now.
Confirmed today from a reliable source that trek has a 32 inch prototype for the DH team to test. Unsure when/if we will see it.
As far as I could tell, I don't think it's a URT. That lower mount on the frame isn't a pivot, it's just the lower attachment point for the plates that that carry the BB. Then there a traditional horst rear end attached to the plates.
It's like the modular rear end angle they were going for fell flat and so they're making it about frame compliance now. It's a dumb idea, and they would be better off just making bikes like Reeb does.
Post a reply to: 2026 MTB Tech Rumors and Innovation - Longer and Slacker