Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain...
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.
I can see the similarities. I honestly do not recall the company that is making the frames for him. Also I do not know if it has...
I can see the similarities. I honestly do not recall the company that is making the frames for him.
Also I do not know if it has been brought up but the Orbea Rallon DH will be getting revisions. Mainly the front triangle will not have the LOCKR storage compartment and the rear seat stay will have a bridge.
After some armchair engineering, I think ideally it would be moulded and adhered to the frame itself and sized so that it makes as much contact...
After some armchair engineering, I think ideally it would be moulded and adhered to the frame itself and sized so that it makes as much contact with the fork as possible, at which point you could relax on the thickness and hardness a bit. It could be a lot of work on more complex frame shapes, but you could also get contact with more than 100 mm of the stanchion on some frames.
They sure are ugly, but I bet they work better than the odi bumpers.
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain...
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain...
Berrecloth's URSA bike appears to have a name now, I spoke to him at the Stevie Smith bike park in the summer and he was uncertain as to when they would become available to the public. Might be sooner rather than later.
Any one hear of enduro rallons breaking? Given that many people ride them full pace on DH race courses often, and there is less suspension absorbing forces, you’d think it happened.
I'll admit to being no physicist, but again, would the weight of the rider not be the largest qualifier for how much energy a brake system...
I'll admit to being no physicist, but again, would the weight of the rider not be the largest qualifier for how much energy a brake system needs in order to stop? The leverage over the wheel is in context to how much mass the wheel has, which given 29 vs 32 XC wheelsets have probably 200~g of difference when they're like for like, the stopping force is focused on the rider, not stopping the wheel.
If someone could break down the maths, would appreciate it.
I stated the 150lb part as I was 150 on 26, 150 on 27.5, and 150 on 29, and I've never felt a need to increase rotor size.
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you...
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you need to make the wheel slow down changes when your lever does. Say you lock the lever at some position and try to spin the wheel by hand. If you spin it by the tire, it's much easier than spinning it by the rotor. The closer to the center you go, the harder you have to push to rotate the wheel against the braking force applied at rotor. Since the ground is the one trying to spin your wheel, the bigger the wheel, the bigger the lever you provide for the ground to overcome your clamping force.
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine.
While I am of the opinion brakes are just KE to heat conversion devices and as such a 32" bike doesn't necessarily need proportional rotors, on my personal 32er I put 200mm rotors on because it's what I had in the garage. It turned out my desire to save $60 superseded my desire to be "right".
I can see the lever theory in the context of RPM being different at a given riding speed for wheels of different sizes, and it could be that the interaction between rotor and pad changes at different rotational speeds. I'm not sure if that's true, but I know there is a difference in how the brakes behave when locked vs. when sliding; maybe there is a braking behavior difference when the rotor is spinning at X rpm vs 1.5X rpm?
There's an old proverb of a man walking through a village with a hat that has one blue side and one green side. The village commenced to arguing about the color of the man's hat. "It's blue!", "It's green!" they yelled.
It could be that this is a multi-colored hat situation. Or maybe this is a situation where the hat is one color, but it's silly to argue about the color of a hat.
I'll admit to being no physicist, but again, would the weight of the rider not be the largest qualifier for how much energy a brake system...
I'll admit to being no physicist, but again, would the weight of the rider not be the largest qualifier for how much energy a brake system needs in order to stop? The leverage over the wheel is in context to how much mass the wheel has, which given 29 vs 32 XC wheelsets have probably 200~g of difference when they're like for like, the stopping force is focused on the rider, not stopping the wheel.
If someone could break down the maths, would appreciate it.
I stated the 150lb part as I was 150 on 26, 150 on 27.5, and 150 on 29, and I've never felt a need to increase rotor size.
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you...
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you need to make the wheel slow down changes when your lever does. Say you lock the lever at some position and try to spin the wheel by hand. If you spin it by the tire, it's much easier than spinning it by the rotor. The closer to the center you go, the harder you have to push to rotate the wheel against the braking force applied at rotor. Since the ground is the one trying to spin your wheel, the bigger the wheel, the bigger the lever you provide for the ground to overcome your clamping force.
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine. While I...
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine.
While I am of the opinion brakes are just KE to heat conversion devices and as such a 32" bike doesn't necessarily need proportional rotors, on my personal 32er I put 200mm rotors on because it's what I had in the garage. It turned out my desire to save $60 superseded my desire to be "right".
I can see the lever theory in the context of RPM being different at a given riding speed for wheels of different sizes, and it could be that the interaction between rotor and pad changes at different rotational speeds. I'm not sure if that's true, but I know there is a difference in how the brakes behave when locked vs. when sliding; maybe there is a braking behavior difference when the rotor is spinning at X rpm vs 1.5X rpm?
There's an old proverb of a man walking through a village with a hat that has one blue side and one green side. The village commenced to arguing about the color of the man's hat. "It's blue!", "It's green!" they yelled.
It could be that this is a multi-colored hat situation. Or maybe this is a situation where the hat is one color, but it's silly to argue about the color of a hat.
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how much difference in force is required at the brake lever. Then decide if that is negligible, noticeable, or impactful.
It’s not just a kinetic energy dissipation problem but that may be a big enough component it overshadows the meaningful effect. But bottom line. We could answer it unequivocally instead of waxing poetic.
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how...
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how much difference in force is required at the brake lever. Then decide if that is negligible, noticeable, or impactful.
It’s not just a kinetic energy dissipation problem but that may be a big enough component it overshadows the meaningful effect. But bottom line. We could answer it unequivocally instead of waxing poetic.
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking force and a 10% longer stopping distance than an otherwise identical 29" bike. Same as the difference between a 180 and 200 rotor. Overall conclusion is that every factor cancels out but wheel radius.
This is a theoretical where the two bikes have identical braking setups, identical weights, and the same rider on each. Obviously the 32 will most likely be a bit heavier, but that's a small difference to the system mass of the rider and bike.
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you...
What matters here is the ratio of wheel diameter vs. rotor diameter. While the overall kinetic energy converted to heat is about the same, the force you need to make the wheel slow down changes when your lever does. Say you lock the lever at some position and try to spin the wheel by hand. If you spin it by the tire, it's much easier than spinning it by the rotor. The closer to the center you go, the harder you have to push to rotate the wheel against the braking force applied at rotor. Since the ground is the one trying to spin your wheel, the bigger the wheel, the bigger the lever you provide for the ground to overcome your clamping force.
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine. While I...
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine.
While I am of the opinion brakes are just KE to heat conversion devices and as such a 32" bike doesn't necessarily need proportional rotors, on my personal 32er I put 200mm rotors on because it's what I had in the garage. It turned out my desire to save $60 superseded my desire to be "right".
I can see the lever theory in the context of RPM being different at a given riding speed for wheels of different sizes, and it could be that the interaction between rotor and pad changes at different rotational speeds. I'm not sure if that's true, but I know there is a difference in how the brakes behave when locked vs. when sliding; maybe there is a braking behavior difference when the rotor is spinning at X rpm vs 1.5X rpm?
There's an old proverb of a man walking through a village with a hat that has one blue side and one green side. The village commenced to arguing about the color of the man's hat. "It's blue!", "It's green!" they yelled.
It could be that this is a multi-colored hat situation. Or maybe this is a situation where the hat is one color, but it's silly to argue about the color of a hat.
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how...
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how much difference in force is required at the brake lever. Then decide if that is negligible, noticeable, or impactful.
It’s not just a kinetic energy dissipation problem but that may be a big enough component it overshadows the meaningful effect. But bottom line. We could answer it unequivocally instead of waxing poetic.
It's pretty simple, 32" is around 8-9% torque reduction. Slightly less than changing rotor sizes (which is around 10%). But changing rotor sizes also changes heat capacity and cooling, which imo is more noticeable. I think it's pretty easy to get used to the brake lever pull being 10% harder or easier. Even for someone like me who thinks "working with one's hands" means using a keyboard and mouse...
You could argue that because the 32" rolls better, gets hung up less, weighs slightly more, etc that it will work the brakes harder. Sure, whatever.
To me a lot of the discussion around brake power is similar to the power vs torque discussion for cars/bikes/ebikes. I think people generally don't understand the difference between torque and power and as a result sometimes end up chasing the wrong thing. For ebikes I think it especially confuses people because the assist percentage is WAY more noticeable and consequential 99% of the time than the peak power/torque number. But for some reason people tend to talk about ebike motor torque and not as much power, and rarely assist.
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking...
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking force and a 10% longer stopping distance than an otherwise identical 29" bike. Same as the difference between a 180 and 200 rotor. Overall conclusion is that every factor cancels out but wheel radius.
This is a theoretical where the two bikes have identical braking setups, identical weights, and the same rider on each. Obviously the 32 will most likely be a bit heavier, but that's a small difference to the system mass of the rider and bike.
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to overcome due to the slower rotation, but maybe only the velocity of the system matters?
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to...
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to overcome due to the slower rotation, but maybe only the velocity of the system matters?
Torque is a function of acceleration/deceleration. The speed at which you are going doesn't have an impact on it.
Another way to view it, which could be more intuitive to some coming from the standpoint of the caliper producing the same force regardless of wheel size, is the definition of work that is force times distance. With the same caliper force and rotor size, the amount of work done by the brake is always equal per rotation of the wheel. The key there is that it is per rotation and not per amount of distance. A 32" wheel rolls 10% further per rotation than a 29" wheel so it requires 10% more distance to stop from a given speed.
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking...
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking force and a 10% longer stopping distance than an otherwise identical 29" bike. Same as the difference between a 180 and 200 rotor. Overall conclusion is that every factor cancels out but wheel radius.
This is a theoretical where the two bikes have identical braking setups, identical weights, and the same rider on each. Obviously the 32 will most likely be a bit heavier, but that's a small difference to the system mass of the rider and bike.
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to...
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to overcome due to the slower rotation, but maybe only the velocity of the system matters?
The way I'm thinking about it is to imagine a bike sitting still with the brake applied. Now push the bike forward and try to make the brake slip. It'll be easier to make the brake slip with a bigger wheel because there's more rotational leverage. You'll need more braking force to prevent the brake from slipping.
Speed will bring in some additional elements like the rotational speed of the wheel (higher with a small wheel) and rotational inertia (higher with a big wheel), but I think those are relatively minor effects compared to the increased leverage you have from the bigger diameter.
Yeah honestly Sean you're active enough on here you gotta do an AMA in this thread post-release once you're allowed to talk about stuff.
Not sure, from the info provided it sounded like Orbea was only tiding up the front triangle weak point and rear end stiffness.
They sure are ugly, but I bet they work better than the odi bumpers.![]()

![]()
Depends on how you define flickable 😭
I just did the logo sorry for the false advertising!
Edit to add: if I ever do design a bike y’all will be the first to hear about it
Any one hear of enduro rallons breaking? Given that many people ride them full pace on DH race courses often, and there is less suspension absorbing forces, you’d think it happened.
Hey, as a fellow designer, I can appreciate that
But will it be a URT?
Classic I drive actually
@TEAMROBOT and I had this same exchange a while back on the 32" forum. We probably still differ in opinion, which is totally fine.
While I am of the opinion brakes are just KE to heat conversion devices and as such a 32" bike doesn't necessarily need proportional rotors, on my personal 32er I put 200mm rotors on because it's what I had in the garage. It turned out my desire to save $60 superseded my desire to be "right".
I can see the lever theory in the context of RPM being different at a given riding speed for wheels of different sizes, and it could be that the interaction between rotor and pad changes at different rotational speeds. I'm not sure if that's true, but I know there is a difference in how the brakes behave when locked vs. when sliding; maybe there is a braking behavior difference when the rotor is spinning at X rpm vs 1.5X rpm?
There's an old proverb of a man walking through a village with a hat that has one blue side and one green side. The village commenced to arguing about the color of the man's hat. "It's blue!", "It's green!" they yelled.
It could be that this is a multi-colored hat situation. Or maybe this is a situation where the hat is one color, but it's silly to argue about the color of a hat.
You could actually walk through the exercise starting from rider mass and velocity and go step by step through the braking chain to figure out how much difference in force is required at the brake lever. Then decide if that is negligible, noticeable, or impactful.
It’s not just a kinetic energy dissipation problem but that may be a big enough component it overshadows the meaningful effect. But bottom line. We could answer it unequivocally instead of waxing poetic.
I had some free time this morning so I made the questionable decision to run through all the math. A 32" bike has ~10% less braking force and a 10% longer stopping distance than an otherwise identical 29" bike. Same as the difference between a 180 and 200 rotor. Overall conclusion is that every factor cancels out but wheel radius.
This is a theoretical where the two bikes have identical braking setups, identical weights, and the same rider on each. Obviously the 32 will most likely be a bit heavier, but that's a small difference to the system mass of the rider and bike.
It's pretty simple, 32" is around 8-9% torque reduction. Slightly less than changing rotor sizes (which is around 10%). But changing rotor sizes also changes heat capacity and cooling, which imo is more noticeable. I think it's pretty easy to get used to the brake lever pull being 10% harder or easier. Even for someone like me who thinks "working with one's hands" means using a keyboard and mouse...
You could argue that because the 32" rolls better, gets hung up less, weighs slightly more, etc that it will work the brakes harder. Sure, whatever.
To me a lot of the discussion around brake power is similar to the power vs torque discussion for cars/bikes/ebikes. I think people generally don't understand the difference between torque and power and as a result sometimes end up chasing the wrong thing. For ebikes I think it especially confuses people because the assist percentage is WAY more noticeable and consequential 99% of the time than the peak power/torque number. But for some reason people tend to talk about ebike motor torque and not as much power, and rarely assist.
Can you explain why the wheel rotating slower on the 32" doesn't help somehow? It seems like there would be less torque on the rotor to overcome due to the slower rotation, but maybe only the velocity of the system matters?
Torque is a function of acceleration/deceleration. The speed at which you are going doesn't have an impact on it.
Another way to view it, which could be more intuitive to some coming from the standpoint of the caliper producing the same force regardless of wheel size, is the definition of work that is force times distance. With the same caliper force and rotor size, the amount of work done by the brake is always equal per rotation of the wheel. The key there is that it is per rotation and not per amount of distance. A 32" wheel rolls 10% further per rotation than a 29" wheel so it requires 10% more distance to stop from a given speed.
The way I'm thinking about it is to imagine a bike sitting still with the brake applied. Now push the bike forward and try to make the brake slip. It'll be easier to make the brake slip with a bigger wheel because there's more rotational leverage. You'll need more braking force to prevent the brake from slipping.
Speed will bring in some additional elements like the rotational speed of the wheel (higher with a small wheel) and rotational inertia (higher with a big wheel), but I think those are relatively minor effects compared to the increased leverage you have from the bigger diameter.
Post a reply to: 2026 MTB Tech Rumors and Innovation - Longer and Slacker