There is no reason for the bushings to be further apart in a single crown fork, inverted or not. It can be a thing with dual...
There is no reason for the bushings to be further apart in a single crown fork, inverted or not. It can be a thing with dual crown inverted forks as the stanchions can travel past lower crown, can thus be longer for a given travel and the bushings can be further apart.
In a classic fork you can extend the lowers past the axle and get additional bushing separation that way.
As for inverted fork benefits, the benefit is that the lower bushing at least and the seals are sitting in a bath of oil and thus should be smoother than in a conventional fork where these parts are not as well lubricated.
Hey @Primoz, sorry but I have to disagree with you on this one. The layout of an inverted single crown fork allows it to have significantly more bushing overlap than a comparable travel RSU fork. This was a frequent talking point at the Fox Podium camp I attended, and while it wasn't initially intuitive for me to understand, it finally clicked when I got out a measuring tape and looked at two comparable travel forks. In short, it all comes down to where the stanchions end up on a fork chassis because the stanchion location forces the designer's hand when it comes to bushing placement.
I've included two badly drawn pictures below that show why that's true, using my 2025 Fox 36 Float and 2026 Podium. I don't know the exact bushing overlap of the 36, and I suspect it's probably a little less than the 38, but the 36 is still capable of being run at 170mm like the Podium or 38, and the pictures do a good job of showing the inherent limitations of a single crown RSU layout if you want to maximize bushing overlap. I apologize in advance for my horrific lack of photoshop-y skills.
TLDR: the stanchion position, arch, and crown on the RSU fork are the things standing in the way of more bushing overlap:
More room for bushing overlap.
Less room for bushing overlap
Why 174mm in my photos? Because according to Fox, the Podium has 174.4mm of bushing overlap compared to 120mm for the 38. That’s a lot more, and according to Fox it's about the same amount as the 40 DH fork.
As you mentioned in your post, one way to get around this limitation on RSU forks is to move the bottom of the fork lowers further down, which allows the stanchion to travel further down at full bottom out. Like you said, "In a classic fork you can extend the lowers past the axle and get additional bushing separation that way":
By stretching the bottom of the fork lowers further down past the axle, you can sneak a longer overall stanchion length into the fork lowers and thereby create more overlap between the upper and lower bushings.
The obvious downside of this design is that your fragile magnesium casting is now in harm's way for rock strikes and other accidents. It's what Fox did on the old long travel 26" 180mm 36 forks, and what Manitou did on the long travel 26" Travis single crown. Probably a few other examples I didn't remember, too:
I suspect fork manufacturers did this on the old 26" forks because there was so little room to work with inside the shorter lowers of a 26" fork, and they moved away from this design when front wheels got bigger and fork lowers were able to be stretched out, meaning they were able to accommodate more stanchion and bushing overlap inside the lowers without having the fragile magnesium fork lower hanging down below the axle.
The bushing overlap problem gets a lot easier to solve on a dual crown RSU fork because the crown can be so much lower profile. On a dual crown fork, the lower crown doesn't have to clear a bike's down tube when you turn the bars, so the lower crown doesn't have to project as far down from the steerer tube as it would on a single crown. This allows you to move the end of the travel range on the stanchion much higher up on the chassis of the fork, which again allows for more bushing overlap in the lowers. As I mentioned earlier, Fox said that the dual crown 40 has about the same amount of bushing overlap as the single crown Podium, which means it has about 45% more overlap than a 38:
The different crown shape and resulting lower crown "stack height" is the main reason why dual crown forks tend to have lower axle-to-crown heights than comparable travel single crown forks. For instance, a 180mm travel Manitou Dorado has a 582mm A2C height, compared to a 180mm travel RS Zeb with a much taller 596mm A2C.
Interestingly, it also results in a stiffer lower crown and arch shape, because both parts don't have to be as arched as they are on a single crown. For instance, look at the height of the arch on that 2025 Fox 40 versus a 36 from the same year. Smaller arch height = stiffer arch.
It was interesting to work through this logic because it means that the design factors that make a RSU dual crown stiffer than a RSU single crown actually compound on each other: two crowns are obviously stiffer than one, but they also mean you can use a lower profile design on the lower crown (which is also stiffer), and this allows a lower profile arch shape (which is stiffer), and those two factors together allow you to sneak a longer overall stanchion length in the lowers and thus create more bushing overlap (which is even stiffer still). Dual crown forks also usually have bolt-on 20mm axles vs. the single-bolt 15mm axle you find on most RSU single crowns, and you end up with a drastically stiffer product.
MTB forks are up against it as well vs. moto forks.
Typical moto forks have one set of bushings affixed to the end of the inner stanchion. They ride in polished ways inside the outer stanchion. The outer stanchion have bushings pressed into them that ride on the inner stanchion. During compression the bushings move away from each other increasing bushing overlap.
The EXT Vaia uses a floating "moto style" bushing setup, as do the Bright inverted forks out of Italy.
Presumably the single crown inverted fork that EXT is working on will have the same floating bushing setup and if it's anything like the Vaia will be an absolute beast!
Like 27 Fox 38, 36, Lyrik, Zeb, latest Mezzer Pro?
I finally had the chance to hop on the latest lyrik in the parking lot, fresh out of the box and I was impressed by the smoothness and sensitivity, hopefully I can try one on the trail but yeah, pretty porky (2.33kg) but looks and at least in the parking lot feels very good for a stock fork.
Still not as frictionless as the Intend I own but still impressive
By the way: I think Twin tube air springs and Glide core air springs matter quite a bit for fork movement under flex. No numbers to back this up whatsoever, just a gut feeling from going coil in a last gen 36.
Apologies for the deviation, but hearing this for years I still haven't grasped the importance of fore-aft stiffness, can someone break it down for me?I can...
Apologies for the deviation, but hearing this for years I still haven't grasped the importance of fore-aft stiffness, can someone break it down for me? I can easily feel torsional stiffness differences when riding, but struggling to see the front to back playing much of a role.
Any impact not 100 % aligned with the angle of the fork will side load the fork to some extent. Square edged hits that are high enough. Landings to flat (pulls the fork forwards). Etc.
In every one of those cases, an infinitely stiff fork will move in the travel even though it's not completely on axis (perpendicular part of the force will generate some more friction). In a very flexy fork it will bend out of the way, off axis, instead of move into the travel.
The reality is closer to the infinitely stiff fork, but any bending in the stanchions still introduces additional friction and binding into the system, which impacts movement along the axis and makes the fork more harsh.
There is no reason for the bushings to be further apart in a single crown fork, inverted or not. It can be a thing with dual...
There is no reason for the bushings to be further apart in a single crown fork, inverted or not. It can be a thing with dual crown inverted forks as the stanchions can travel past lower crown, can thus be longer for a given travel and the bushings can be further apart.
In a classic fork you can extend the lowers past the axle and get additional bushing separation that way.
As for inverted fork benefits, the benefit is that the lower bushing at least and the seals are sitting in a bath of oil and thus should be smoother than in a conventional fork where these parts are not as well lubricated.
Hey @Primoz, sorry but I have to disagree with you on this one. The layout of an inverted single crown fork allows it to have...
Hey @Primoz, sorry but I have to disagree with you on this one. The layout of an inverted single crown fork allows it to have significantly more bushing overlap than a comparable travel RSU fork. This was a frequent talking point at the Fox Podium camp I attended, and while it wasn't initially intuitive for me to understand, it finally clicked when I got out a measuring tape and looked at two comparable travel forks. In short, it all comes down to where the stanchions end up on a fork chassis because the stanchion location forces the designer's hand when it comes to bushing placement.
I've included two badly drawn pictures below that show why that's true, using my 2025 Fox 36 Float and 2026 Podium. I don't know the exact bushing overlap of the 36, and I suspect it's probably a little less than the 38, but the 36 is still capable of being run at 170mm like the Podium or 38, and the pictures do a good job of showing the inherent limitations of a single crown RSU layout if you want to maximize bushing overlap. I apologize in advance for my horrific lack of photoshop-y skills.
TLDR: the stanchion position, arch, and crown on the RSU fork are the things standing in the way of more bushing overlap:
More room for bushing overlap.
Less room for bushing overlap
Why 174mm in my photos? Because according to Fox, the Podium has 174.4mm of bushing overlap compared to 120mm for the 38. That’s a lot more, and according to Fox it's about the same amount as the 40 DH fork.
As you mentioned in your post, one way to get around this limitation on RSU forks is to move the bottom of the fork lowers further down, which allows the stanchion to travel further down at full bottom out. Like you said, "In a classic fork you can extend the lowers past the axle and get additional bushing separation that way":
By stretching the bottom of the fork lowers further down past the axle, you can sneak a longer overall stanchion length into the fork lowers and thereby create more overlap between the upper and lower bushings.
The obvious downside of this design is that your fragile magnesium casting is now in harm's way for rock strikes and other accidents. It's what Fox did on the old long travel 26" 180mm 36 forks, and what Manitou did on the long travel 26" Travis single crown. Probably a few other examples I didn't remember, too:
I suspect fork manufacturers did this on the old 26" forks because there was so little room to work with inside the shorter lowers of a 26" fork, and they moved away from this design when front wheels got bigger and fork lowers were able to be stretched out, meaning they were able to accommodate more stanchion and bushing overlap inside the lowers without having the fragile magnesium fork lower hanging down below the axle.
The bushing overlap problem gets a lot easier to solve on a dual crown RSU fork because the crown can be so much lower profile. On a dual crown fork, the lower crown doesn't have to clear a bike's down tube when you turn the bars, so the lower crown doesn't have to project as far down from the steerer tube as it would on a single crown. This allows you to move the end of the travel range on the stanchion much higher up on the chassis of the fork, which again allows for more bushing overlap in the lowers. As I mentioned earlier, Fox said that the dual crown 40 has about the same amount of bushing overlap as the single crown Podium, which means it has about 45% more overlap than a 38:
The different crown shape and resulting lower crown "stack height" is the main reason why dual crown forks tend to have lower axle-to-crown heights than comparable travel single crown forks. For instance, a 180mm travel Manitou Dorado has a 582mm A2C height, compared to a 180mm travel RS Zeb with a much taller 596mm A2C.
Interestingly, it also results in a stiffer lower crown and arch shape, because both parts don't have to be as arched as they are on a single crown. For instance, look at the height of the arch on that 2025 Fox 40 versus a 36 from the same year. Smaller arch height = stiffer arch.
It was interesting to work through this logic because it means that the design factors that make a RSU dual crown stiffer than a RSU single crown actually compound on each other: two crowns are obviously stiffer than one, but they also mean you can use a lower profile design on the lower crown (which is also stiffer), and this allows a lower profile arch shape (which is stiffer), and those two factors together allow you to sneak a longer overall stanchion length in the lowers and thus create more bushing overlap (which is even stiffer still). Dual crown forks also usually have bolt-on 20mm axles vs. the single-bolt 15mm axle you find on most RSU single crowns, and you end up with a drastically stiffer product.
Okay, I wasn't talking about specific products, I was talking more generally. Lets say architecturaly there is no reason for either to be any different. Theoretically upside down forks have a bit of an edge as the stanchion could theoretically move up all the way into the crown, but if you do that, you have to push the stanchion past the axle in an RSU fork to make it fair. The point is, you're working in the same space generally. How much bushing spacing you get is just a matter of how you lay things out.
The thing I was trying to point out is that with a single crown RSU or an upside down fork, or a dual crown RSU you are limited in fitting the crown (whichever shape it takes), the stanchions and the lowers including the bushings and their spacing, and the travel you want, into the space between the lower headset bearing and the axle, unless you protrude below the axle. With a dual crown upside-down fork, the outer tubes extend past the lower crown all the way to the upper crown. THAT is the architectural difference I was pointing out.
Looking at the 38 and Podium specifically, while the images ar enot aligned 100 % ideally, you can still see the crown reaches a bit higher on the Podium than it does on the 38 as the 38 has to drop it for the adjustors (which are a lot thicker than on the Podium) to clear the downtube. That loses you a few mm. Then you can see the Podium extends below the axle by quite a bit. While on an upside down fork this doesn't give you much of an advantage for bushing overlap per-se, you can compare it to the 38 which has the adjuster and the bottom of the (interior of the) lowers higher than the axle. So comparatively the 38 is robbed of some overall length as the stanchions cannot physically extend past the axle (like they could on the 26" 36) while theoretically on the Podium they can extend up into the crown. TL;DR: I think the 38 could generally have a similar bushing spacing if FOX wanted to achieve that (and as noted by others, did have a big increase in the latest update), it's just that apparently the design philosophies differed a bit.
Also, for the bit extending past the axle, is it realistic for it to hit a rock? If the fork is hitting a rock, your whole rear end will hit it as well plus the cranks, the pedal, your foot, etc. Except in a crash, but in that case, anything can hit a rock...
Shame that it’s only 160 travel, 170 (or 180) and I would be really interested.
Yeah, I feel like the type of people who are going to run an inverted fork are going to run it on 170 so if they're going to choose just one size then 170 would make more sense.
The fork seems interesting but it also seems like it was a prototype they decided to pull out of the back of the closet and release to "see what happens"
Hey @Primoz, sorry but I have to disagree with you on this one. The layout of an inverted single crown fork allows it to have significantly more bushing overlap than a comparable travel RSU fork. This was a frequent talking point at the Fox Podium camp I attended, and while it wasn't initially intuitive for me to understand, it finally clicked when I got out a measuring tape and looked at two comparable travel forks. In short, it all comes down to where the stanchions end up on a fork chassis because the stanchion location forces the designer's hand when it comes to bushing placement.
I've included two badly drawn pictures below that show why that's true, using my 2025 Fox 36 Float and 2026 Podium. I don't know the exact bushing overlap of the 36, and I suspect it's probably a little less than the 38, but the 36 is still capable of being run at 170mm like the Podium or 38, and the pictures do a good job of showing the inherent limitations of a single crown RSU layout if you want to maximize bushing overlap. I apologize in advance for my horrific lack of photoshop-y skills.
TLDR: the stanchion position, arch, and crown on the RSU fork are the things standing in the way of more bushing overlap:
Why 174mm in my photos? Because according to Fox, the Podium has 174.4mm of bushing overlap compared to 120mm for the 38. That’s a lot more, and according to Fox it's about the same amount as the 40 DH fork.
As you mentioned in your post, one way to get around this limitation on RSU forks is to move the bottom of the fork lowers further down, which allows the stanchion to travel further down at full bottom out. Like you said, "In a classic fork you can extend the lowers past the axle and get additional bushing separation that way":
The obvious downside of this design is that your fragile magnesium casting is now in harm's way for rock strikes and other accidents. It's what Fox did on the old long travel 26" 180mm 36 forks, and what Manitou did on the long travel 26" Travis single crown. Probably a few other examples I didn't remember, too:
I suspect fork manufacturers did this on the old 26" forks because there was so little room to work with inside the shorter lowers of a 26" fork, and they moved away from this design when front wheels got bigger and fork lowers were able to be stretched out, meaning they were able to accommodate more stanchion and bushing overlap inside the lowers without having the fragile magnesium fork lower hanging down below the axle.
The bushing overlap problem gets a lot easier to solve on a dual crown RSU fork because the crown can be so much lower profile. On a dual crown fork, the lower crown doesn't have to clear a bike's down tube when you turn the bars, so the lower crown doesn't have to project as far down from the steerer tube as it would on a single crown. This allows you to move the end of the travel range on the stanchion much higher up on the chassis of the fork, which again allows for more bushing overlap in the lowers. As I mentioned earlier, Fox said that the dual crown 40 has about the same amount of bushing overlap as the single crown Podium, which means it has about 45% more overlap than a 38:
The different crown shape and resulting lower crown "stack height" is the main reason why dual crown forks tend to have lower axle-to-crown heights than comparable travel single crown forks. For instance, a 180mm travel Manitou Dorado has a 582mm A2C height, compared to a 180mm travel RS Zeb with a much taller 596mm A2C.
Interestingly, it also results in a stiffer lower crown and arch shape, because both parts don't have to be as arched as they are on a single crown. For instance, look at the height of the arch on that 2025 Fox 40 versus a 36 from the same year. Smaller arch height = stiffer arch.
It was interesting to work through this logic because it means that the design factors that make a RSU dual crown stiffer than a RSU single crown actually compound on each other: two crowns are obviously stiffer than one, but they also mean you can use a lower profile design on the lower crown (which is also stiffer), and this allows a lower profile arch shape (which is stiffer), and those two factors together allow you to sneak a longer overall stanchion length in the lowers and thus create more bushing overlap (which is even stiffer still). Dual crown forks also usually have bolt-on 20mm axles vs. the single-bolt 15mm axle you find on most RSU single crowns, and you end up with a drastically stiffer product.
https://www.vitalmtb.com/forums/The-Hub,2/Are-Upside-Down-forks-really-flexy,11099?page=0

MTB forks are up against it as well vs. moto forks.
Typical moto forks have one set of bushings affixed to the end of the inner stanchion. They ride in polished ways inside the outer stanchion. The outer stanchion have bushings pressed into them that ride on the inner stanchion. During compression the bushings move away from each other increasing bushing overlap.
The EXT Vaia uses a floating "moto style" bushing setup, as do the Bright inverted forks out of Italy.
Presumably the single crown inverted fork that EXT is working on will have the same floating bushing setup and if it's anything like the Vaia will be an absolute beast!
Since we’re in the topic,
Anyone knows the latest forks Bushing overlap?
Like 27 Fox 38, 36, Lyrik, Zeb, latest Mezzer Pro?
I finally had the chance to hop on the latest lyrik in the parking lot, fresh out of the box and I was impressed by the smoothness and sensitivity, hopefully I can try one on the trail but yeah, pretty porky (2.33kg) but looks and at least in the parking lot feels very good for a stock fork.
Still not as frictionless as the Intend I own but still impressive
Current Fox 38 should be 140mm+- (20mm up from previous 38), current Fox 36 is actually 165mm. No idea about the Rockshox offerings.
By the way: I think Twin tube air springs and Glide core air springs matter quite a bit for fork movement under flex. No numbers to back this up whatsoever, just a gut feeling from going coil in a last gen 36.
What do you think of the DT Swiss "Coil Pair" and "Plushport" technologies?
Coilpair Technology | DT Swiss
Any impact not 100 % aligned with the angle of the fork will side load the fork to some extent. Square edged hits that are high enough. Landings to flat (pulls the fork forwards). Etc.
In every one of those cases, an infinitely stiff fork will move in the travel even though it's not completely on axis (perpendicular part of the force will generate some more friction). In a very flexy fork it will bend out of the way, off axis, instead of move into the travel.
The reality is closer to the infinitely stiff fork, but any bending in the stanchions still introduces additional friction and binding into the system, which impacts movement along the axis and makes the fork more harsh.
Okay, I wasn't talking about specific products, I was talking more generally. Lets say architecturaly there is no reason for either to be any different. Theoretically upside down forks have a bit of an edge as the stanchion could theoretically move up all the way into the crown, but if you do that, you have to push the stanchion past the axle in an RSU fork to make it fair. The point is, you're working in the same space generally. How much bushing spacing you get is just a matter of how you lay things out.
The thing I was trying to point out is that with a single crown RSU or an upside down fork, or a dual crown RSU you are limited in fitting the crown (whichever shape it takes), the stanchions and the lowers including the bushings and their spacing, and the travel you want, into the space between the lower headset bearing and the axle, unless you protrude below the axle. With a dual crown upside-down fork, the outer tubes extend past the lower crown all the way to the upper crown. THAT is the architectural difference I was pointing out.
Looking at the 38 and Podium specifically, while the images ar enot aligned 100 % ideally, you can still see the crown reaches a bit higher on the Podium than it does on the 38 as the 38 has to drop it for the adjustors (which are a lot thicker than on the Podium) to clear the downtube. That loses you a few mm. Then you can see the Podium extends below the axle by quite a bit. While on an upside down fork this doesn't give you much of an advantage for bushing overlap per-se, you can compare it to the 38 which has the adjuster and the bottom of the (interior of the) lowers higher than the axle. So comparatively the 38 is robbed of some overall length as the stanchions cannot physically extend past the axle (like they could on the 26" 36) while theoretically on the Podium they can extend up into the crown.
TL;DR: I think the 38 could generally have a similar bushing spacing if FOX wanted to achieve that (and as noted by others, did have a big increase in the latest update), it's just that apparently the design philosophies differed a bit.
Also, for the bit extending past the axle, is it realistic for it to hit a rock? If the fork is hitting a rock, your whole rear end will hit it as well plus the cranks, the pedal, your foot, etc. Except in a crash, but in that case, anything can hit a rock...
Sounds like someone already got their hands on the KYB fork
https://www.testpilot.bike/magazin/en/kyb-160-mm-coil-fork-review
Shame that it’s only 160 travel, 170 (or 180) and I would be really interested.
Only 3 spring rates to cover 55-100kg seems... too few.
Yeah, I feel like the type of people who are going to run an inverted fork are going to run it on 170 so if they're going to choose just one size then 170 would make more sense.
The fork seems interesting but it also seems like it was a prototype they decided to pull out of the back of the closet and release to "see what happens"
Post a reply to: Suspension Component Technology/Functionality Discussion