Frame |
Rocky Mountain |
Altitude Carbon C70 |
XS w/ 26" wheels. Ride9 option 3. |
Rear Shock |
Manitou |
Mara Pro |
210x55 for 150mm of travel. Stock rocky eyelet hardware working well. Running 90 PSI in Mara Pro with all compression/rebound open. |
Fork |
Manitou |
Mezzer Pro |
160mm Mezzer Pro has roughly 20PSI in Air spring and 35PSI in IRT with all compression and rebound open. |
Headset |
Cane Creek |
FORTY-SERIES ZERO STACK |
|
Handlebar |
Other |
ProTaper JUnit |
680mm wide kids bars |
Stem |
Other |
ProTaper |
35mm Length : 31.8 Clamp Diamter |
Grips |
Other |
ProTaper JUnit 26mm |
Kid sized grips |
Brakes |
Hayes |
Dominion A2 |
With Kids SFL Levers (Small Finger Lever) |
Brake Levers |
Hayes |
SFL - Small Finger Levers |
Kids specific levers |
Shifters |
Shimano |
XT 8100 |
Mounted to Hayes Peacemaker |
Front Derailleur |
------- |
|
|
Rear Derailleur |
Shimano |
XT RD-M8100 |
12sp |
Chainguide |
Other |
Rocky Mountain Spirit Guide |
|
Cranks |
SRAM |
X1 155mm |
|
Chainrings / Sprocket |
Other |
Wolftooth Switch 30t |
|
Bottom Bracket |
SRAM |
PF92 DUB |
2mm spacer on drive side |
Chain |
Shimano |
XT 8100 |
|
Cassette / Rear Cog |
Shimano |
XT CS-M8100 12-Speed |
|
Pedals |
Crankbrothers |
Stamp Composite Small |
|
Front Rim |
Stan's NoTubes |
Arch MK3 26" |
i26mm |
Rear Rim |
Stan's NoTubes |
Arch MK3 26" |
i26mm |
Hubs |
DT Swiss |
DT350 |
Microspline |
Spokes |
DT Swiss |
Competition Race |
|
Front Tire |
Maxxis |
Minion DHR2 2.4 26" 3C |
|
Rear Tire |
Maxxis |
Minion DHR2 2.4 26" DC |
|
Saddle |
SDG |
Fly Jr. |
|
Seatpost |
OneUp Components |
V2 150mm Dropper |
240 PSI - works great for 80lb 10yro |
Seatpost Clamp |
Other |
Stock Rocky Mountain |
|
cheapondirt
4/16/2022 3:41 PM
Svinyard
4/16/2022 4:44 PM
Yeah frame was used and I wanted to get fresh bearings in all of it. The only bearings that are blind are the two for the lower main pivot. The chainstay bearings etc can all just be pressed out from behind. I used the AltAlt bearing set to do almost all of it and certainly re-install them all. Rocky Mountain has a decent manual with drawings that show the exploded view, bearings and also torque values.
1- Chainstay bearings, linkage bearings: The AltAlt can press them out
2- Main pivot blind bearings - I used a blind bearing puller from Motion Pro and its smallest collet. Worked great. That being said, its an expensive too. Thankfully there is a metal spacer between the two bearings. It has 4 notches in it (two on each side) that a flathead screw drive or other punch could be used to slowly knock them out. AltAlt does the install. When you install, do the drive side first and don't overpress them as the spacer needs to fit in there and it does provide some preload on the bearings. You don't just smash both bearings in all the way otherwise they are overloaded.
3- The shock eyelet bearings - these are easiest to remove with a vise with softjaws (not the add-on softjaws but legit sawjaws built in or a simple wood vise). You clamp the eyelet and rotate it until the bearing cup comes out. Then you can use the AltAlt and the metal spacer to press out the bearings and install them.
cheapondirt
4/17/2022 9:32 AM
Fox
4/16/2022 7:27 AM
Svinyard
4/16/2022 8:41 AM
Whattheheel
4/16/2022 9:20 AM
iceman2058
4/16/2022 5:20 AM