Accessibility Widget: On | Off
Liked a bike check Specialized Stumpjumper EVO 1/20/2020 2:53 AM
Specialized Stumpjumper EVO
Liked a bike check Forbidden Druid 1/19/2020 10:25 AM
Forbidden Druid
Liked a bike check Transition Sentinel- The Raw Dawg 1/16/2020 10:22 AM
Transition Sentinel- The Raw Dawg
Liked a bike check Homemade Trail Bike 12/26/2019 1:13 AM
Homemade Trail Bike
Liked a bike check Homemade Enduro Race Bike 12/26/2019 1:10 AM
Homemade Enduro Race Bike
Liked a bike check Tikbalang MK1 Titanium Downhill Enduro bike 12/24/2019 2:27 AM
Tikbalang MK1 Titanium Downhill Enduro bike
Liked a bike check Rocky Mountain Instinct BC Alloy Custom Build 11/26/2019 11:33 PM
Rocky Mountain Instinct BC Alloy Custom Build
Liked a bike check Peppermint Patty 11/25/2019 1:16 AM
Peppermint Patty
Liked a bike check project12 - Vertigo 11/25/2019 1:11 AM
project12 - Vertigo
Liked a bike check Bad Hombre 11/19/2019 3:07 AM
Bad Hombre
Liked a bike check Nicolai G1 11/17/2019 12:50 AM
Nicolai G1
Liked a bike check The Smashing Pumpkin 11/12/2019 1:02 AM
The Smashing Pumpkin
Liked a bike check Commencal CLASH Custom 2020 11/12/2019 1:01 AM
Commencal CLASH Custom 2020
Added a comment to alen3dpro's bike check 11/8/2019 12:29 PM
RAGING BULL

180cm...

0 0 0

This setup has 16 comments.

Liked a bike check Wood and Bourbon 11/8/2019 10:23 AM
Wood and Bourbon
Liked a bike check patientZERO #18 11/8/2019 4:52 AM
patientZERO #18
Added a comment to alen3dpro's bike check 11/6/2019 9:33 AM
RAGING BULL

TNX

It is TAILOR made frame (nicolai will basicly do you everything you desire just pay them 700-800 euros extra) the CS and SS are from older model and front is from new era bondet together i have a frankenbike for shure …i also have new longer set (450) but you know what i did not like it…only benefit i found on longer set is suspension somehow works plusher not so skippy but once ill reduce compression on my storia (not a problem just need to send shock back to italy) i think i am on to something…kinda braking the modern rules here (long low slack)…no not for me…i like short back end not low (bikes are getting dengerusly close to the ground nowadays) long front is good and 64 is slack enough…also preferred 50mm stem over 35mm…if i could do it again and build another custom geometry, i made some changes 79sta instead of 77 and 625 stack instead of 608 but not in lover bb just bigger ht 64 ha ….
back to the cs i also did custom bushings from iglidur A200 and cable holder and some fine machining near bb area so i can run flip chip in high position….swing-arm is now stiction free…will post some pictures with description if interest…

i think you look at guards for lower legs (made from carbon and i wrapped them in car wrap foil) google x fusion metric and you will see original look

see ya

0 0 0

This setup has 16 comments.

Added a comment to alen3dpro's bike check 11/6/2019 2:53 AM
RAGING BULL

what a lovely surprise…tnx…have some nice parts for it in order…will update pictures once done and try to do some proper photos of it…bad light and average smartphone…
…see ya...

0 0 0

This setup has 16 comments.

Added a comment to alen3dpro's bike check 11/5/2019 8:30 AM
RAGING BULL

i think initial bite is a bit stronger with trickstuf and they dont overheat despite being organic..beding process is a bit longer with trickstuf but once done they absolutley work as promoted...shimano metal pads with cooling fins did work ok (braking power was there) but they just did not stay in place, rateling and rubing on rotor made me mad so i replace them.
see ya

0 0 0

This setup has 16 comments.